Door Installation Cost in Minnesota: What to Budget for Entry, Patio, and Storm Doors (2026)

I'll be straight up front: we're not a standalone door shop. Modex installs doors when we're already replacing your windows, because the door brands we trust — ProVia, Pella, and Kolbe — are the same companies that make the windows we pull on every job. We're not chasing a $400 storm-door call across town. We're putting in a ProVia Signet entry door while the crew is also swapping six casements on the same house.

Most "door cost" articles online are written by lead-gen sites that have never personally hung a door, never flashed a sill in February, never had a homeowner call in April because the bottom seal froze to the threshold. I have. What follows is the actual 2026 Twin Cities range — installed, not "starting at," and broken down by what really drives the number. The quick version lives at Door Installation Cost in Minnesota: What You'll Actually Pay. This piece goes deeper.

The 2026 Twin Cities Door Cost Cheat Sheet

Those are 2026 numbers, installed, for the Twin Cities metro. Eden Prairie, Minnetonka, Edina, Wayzata, Bloomington — pricing tracks across the western suburbs. ProVia raised list prices about 5% across steel and fiberglass for 2026 (Energy Swing Windows 2026 ProVia Door Guide), and those increases are baked into the numbers above.

A quick note on Minnesota code: any new exterior door you install in a heated space has to meet a U-factor of 0.32 or better under current Minnesota Residential Energy Code (Chapter 1322), and that requirement is tightening to 0.28 in Climate Zone 6 — which covers the entire Twin Cities metro — as the updated code rolls in (Fresh Energy on the 2024 MN residential energy code update). Sliding glass doors also have to test at 0.3 cfm/ft² air infiltration or lower. Every door I install meets or beats the new spec — but if you're shopping big-box doors, check the NFRC label before you buy.

Entry Doors: Steel vs. Fiberglass vs. Solid Wood

The entry door category is where homeowners get the most surprised by price. A box-store steel slab and a custom ProVia Signet with sidelights are both "an entry door," and they can be $15,000 apart.

Steel Entry Doors — $1,200 to $3,000 Installed

Steel is the cheapest insulated entry door you can put in a Minnesota home. The slab is a thin-gauge steel skin over a polyurethane foam core, and it does an honest job of keeping cold out. I install steel entry doors when budget is the primary driver — rentals, side doors, garage-to-house doors, and basic three-season cabin builds. Box-store steel slabs come in around $400-$1,000 for the door alone; once you add a Twin Cities install with proper flashing and hardware, you're at $1,200-$3,000 all-in. ProVia's Legacy steel sits at the top of the range.

Where steel falls short in Minnesota:

• The skin dents. A baseball, a snow shovel, a stray boot — they leave marks you can't fully fix.
• Temperature swings cause the steel skin to expand and contract differently than the wood frame. Paint can crack at the edges within a few years.
• The thermal break on cheaper steel doors is poor. At -20°F, I've put my hand on a steel slab and felt cold radiating through. Fiberglass doesn't do that.

If your steel door budget is under $1,500 installed, you're almost certainly looking at a box-store product. That's fine for a basement side door. It's not what I'd put on the front of your house.

Fiberglass Entry Doors — $5,000 to $20,000 Installed

This is where ProVia and Pella live, and it's where I spend most of my entry-door installs. Fiberglass is the right answer for a Minnesota front door for three reasons: it doesn't dent, it doesn't move with temperature, and you can get it in finishes that look like real wood (because the molds are pressed from real wood grain).

ProVia 2026 fiberglass tiers, installed:

Those numbers are pulled from current 2026 ProVia dealer guides (Adnan ProVia 2026 Cost Guide) and cross-checked against what we're quoting in the Twin Cities. Pella's fiberglass entry doors land in roughly the Heritage-to-Signet range — $5,500-$13,000 installed. Kolbe doesn't really play in pure fiberglass; if a homeowner asks me for a "Kolbe door," they want wood or aluminum-clad wood, which is the next section.

The biggest single price driver inside fiberglass is glass. Flush slabs sit at the bottom of each tier. A half-lite or three-quarter-lite package adds $800-$2,500. Sidelights add $1,500-$3,500 per side. A transom adds $1,200-$2,800. By the time you've configured a Signet or Embarq with full sidelights and a transom, you're in the $15,000-$25,000 range.

ProVia is what I default to because their catalog is the deepest in the industry and the install hardware is better than what I see at the same price point elsewhere. More at ProVia Windows and Doors Cost: What Twin Cities Homeowners Actually Pay.

Solid Wood Entry Doors — $6,500 to $15,000+ Installed

Solid wood is the highest tier and a real product, not a vanity choice. I install solid wood entry doors on Lake Minnetonka tear-downs, historic Edina remodels, and a handful of Wayzata new-builds every year. Kolbe is my go-to here — mahogany, white oak, and knotty alder are the most common species. A 36×80 mahogany slab runs $2,000-$4,000 alone; add custom sidelights, hand-finishing, and proper Minnesota sill flashing, and you're at $10,000-$15,000.

The honest tradeoff: a solid wood door is the most beautiful door you can put on a Minnesota house. It also needs maintenance you're not used to — refinish the exterior face every 3-5 years depending on sun exposure. South-facing doors with no overhang are the hardest; UV cooks the finish. If you're spending $10,000 on a wood entry door and you don't have an overhang protecting it, I'll usually push back. That money is better spent on a ProVia Embarq with a wood-look finish that doesn't need refinishing.

Patio Doors: Sliding, French, and Multi-Slide

Patio doors are where the price ceiling really opens up. A basic 6-foot vinyl slider is $3,500 installed. A 16-foot lift-slide with multipoint locks is $25,000+. Same category on a quote sheet, nothing alike in reality.

Sliding Patio Doors — $3,500 to $7,500 Installed

The traditional 6-foot or 8-foot two-panel slider is what's on most Twin Cities homes built between 1985 and 2010. Vinyl is the cheapest material; fiberglass and aluminum-clad wood are higher. A Pella 250 Series vinyl slider runs $750-$2,400 for the door alone, installed pricing lands $3,500-$5,500 with proper sill flashing and a triple-pane upgrade. Step up to a fiberglass-frame slider and you're at $5,500-$7,500.

What you're really paying for at the high end:

• Glass package. Low-E coatings, argon fill, triple-pane. For a Minnesota patio door, I push triple-pane on anything over $5,000 installed. The comfort difference standing next to a triple-pane slider at -10°F is dramatic.
• Hardware. Cheap rollers seize up in 5-7 years. The Pella and ProVia rollers I install are rated for 100,000+ cycles.
• Width. Going from a 6-foot to an 8-foot slider isn't just 33% more glass — it's a heavier panel that needs beefier rollers and tracks. Expect $1,000-$1,800 more for the 8-foot.

ProVia Endure sliders and Pella Lifestyle Series are my two go-tos. ProVia is generally a few hundred dollars less for the same configuration, with comparable performance.

French / Swing Patio Doors — $5,000 to $10,500 Installed

French doors swing open instead of sliding. They look better than sliders on traditional homes, they seal tighter (because the latch pulls the door against the weatherstrip instead of riding on a track), and they're harder to install correctly. ProVia French doors run $3,000-$6,000 for the door, $5,000-$8,000 installed; Kolbe Ultra Series and Pella Architect Series push the top of the range.

The Minnesota-specific catch with French doors:

In-swing French doors take up floor space inside the room. Out-swing doors don't — but in our climate, out-swing is harder to weatherproof and screen options are limited. I install in-swing 90% of the time and steer homeowners toward retractable screens.

Kolbe is the most beautiful door in this category but also the longest lead time — expect 14-18 weeks for a Kolbe order. ProVia is usually $1,500-$2,500 less than the Kolbe equivalent for a similar configuration.

Multi-Slide and Lift-Slide Patio Doors — $12,000 to $25,000+

This is the "open up the whole back of the house" category. Three to six panels, 12 to 24 feet wide, stacking or pocketing into a wall. I install one or two of these a year, usually on lake homes around Minnetonka or Excelsior.

The doors are expensive, but the bigger budget driver is structural. Going from a standard 6-foot opening to a 16-foot opening means a structural header upgrade — permit, engineer's stamp, and a crew that knows how to do it without dropping your second floor. Plan the project as a whole: $15,000-$25,000 for the door, $3,000-$8,000 for structural work, plus interior finish. A real multi-slide is a $25,000-$40,000 total scope.

Storm Doors: $425 to $1,200, and Worth Doing Right

Storm doors are the cheapest category and the one homeowners think about the least. That's a mistake — a bad storm door will trap heat against your new fiberglass entry door, warp it, and void the manufacturer warranty.

Full-View Storm Doors — $700 to $1,200 Installed

Full-view storm doors are almost all glass. They show off your entry door, they look clean, and they're what most of my customers want. ProVia Deluxe full-view runs about $700 installed; the Decorator series with custom glass starts around $900 and goes up from there. Larson's full-view storm doors land in the same range.

The catch: full-view storm doors on south or west exposures are a heat trap. I've measured 140°F surface temperatures on a ProVia entry door behind a full-view storm in July. That's enough to bubble paint, warp the slab, and crack the seal between the glass and the frame.

The fix: ProVia and Larson both make full-view storm doors with a removable glass panel that swaps out to a full screen in summer. That's the version I install on south- and west-facing entries. Adds $100-$200 to the price but solves the heat-trap problem completely.

Ventilating / Retractable-Screen Storm Doors — $475 to $1,000 Installed

Ventilating storm doors have two glass panels that slide up or down with a screen behind them. Retractable-screen models — Larson's Platinum line is the one I install most often — hide the screen inside the frame and pull it down when you want air. Retractable models run $150-$250 more than basic ventilating doors but make a real difference on a high-use entry. Good choice for high-traffic side entries, mudroom entries, doors with kids and dogs.

Basic Aluminum Storm Doors — $425 to $700 Installed

The plain aluminum storm door from a big-box store, installed by my crew, is at the bottom of the range. We do install these occasionally — usually on rentals or when a homeowner specifically asks for the cheapest option. I won't pretend it'll last 20 years. Expect 8-12 years and a thinner closer mechanism that needs adjustment more often.

What Actually Drives Your Final Price

Across all three categories, the same handful of factors push the final number up or down:

• Rough opening condition. Twin Cities homes built before 1995 often have openings that aren't plumb, square, or properly flashed. The quote reflects what the opening actually needs — not what the brochure assumes.
• Sill flashing and subfloor. Pulling an old door and discovering rotted subfloor is the most common surprise on a door project. Budget a 10-15% contingency on any door in a home older than 30 years.
• Sidelights and transoms. These double or triple the price of a single-door install. Often the difference between a "$5,000 door" budget and a $15,000 reality.
• Hardware finish. A ProVia handle set in oil-rubbed bronze is $180. The same handle in designer matte black with a multipoint lock is $650.
• Custom color or finish. Add $300-$1,200 for non-standard paint or stain.
• Glass package. Triple-pane vs double-pane, low-E coatings, decorative glass — the glass is often half the price of the door.
• Permitting. Minneapolis, St. Paul, Edina and a handful of suburbs require permits when you change the rough opening size. The permit itself is $75-$200; the inspection schedule can add a week.

What I Don't Love About the Door Category

Honest moment: doors are the trade where I see the widest gap between "great install" and "terrible install" in the Twin Cities. The product matters less than the install. A $1,200 storm door installed by my crew will outlast a $4,000 ProVia entry door installed badly.

What I see most often when I'm called out to fix someone else's door work:

• Sills not flashed. Water gets behind the threshold and rots the subfloor. Five years later there's a soft spot inside the door and a smell.
• Hinges not shimmed. The door sags within a year, the latch stops catching, and the homeowner thinks the door is defective. It's not. The install was rushed.
• Storm doors hung without ventilation. Heat trap, warped slabs, voided warranties.

These aren't ProVia or Pella or Kolbe problems. They're install problems. Doors are deceptively easy to install badly. The difference shows up in year 3, not year 1.

How Modex Quotes a Door Project

Free measurement visit, written quote within 48 hours, one number per scope. Not per-item itemization — one number for "ProVia Signet entry door, sidelights, full install, painted to match." If you want to compare Signet vs. Embarq, I'll write two separate scopes with two separate numbers so you can see the actual delta.

Because we're not a standalone door specialist, the most cost-effective time to do doors with Modex is when we're already on your house doing windows. Crew is already mobilized, doors come from the same manufacturers, and that usually saves a few hundred dollars per door versus a standalone visit. More on the window-and-door scope at /window-replacement-minneapolis. My honest read on the ProVia catalog is at ProVia Windows Reviews: A Minnesota Contractor's Honest Take. If you're considering a whole-house window project alongside doors, is it cheaper to replace all your windows at once? covers the per-window math, and whether you need a permit to replace windows in MN covers the permit side.

FAQ

What's the average cost to install an entry door in Minnesota?

A mid-tier fiberglass entry door installed in the Twin Cities runs $5,000-$8,500 for a single ProVia Heritage or Ascent without sidelights. Step up to Signet or Embarq with full sidelights and a transom and you're in the $12,000-$25,000 range. Steel slabs start around $1,200 installed; custom wood and high-end Kolbe configurations can push past $15,000.

How much does a sliding patio door cost installed in the Twin Cities?

A standard 6-foot sliding patio door runs $3,500-$5,500 installed in vinyl. Step up to fiberglass or aluminum-clad wood and you're at $5,500-$7,500. An 8-foot configuration adds roughly $1,000-$1,800.

Are storm doors worth it in Minnesota?

Yes — but only the right type, installed correctly. Full-view storm doors on south- and west-facing entries can trap heat and damage your entry door. A vented or swappable-panel model fixes that. Budget $700-$1,000 installed for a storm door that'll last 15+ years.

Do new doors in Minnesota have to meet a specific energy code?

Yes. Under current Minnesota Residential Energy Code (Chapter 1322), exterior doors and patio doors must hit a U-factor of 0.32 or better, and that's tightening to 0.28 in Climate Zone 6 — which covers the entire Twin Cities — as the updated code rolls in. Sliding glass doors also have to test at 0.3 cfm/ft² air infiltration or lower. Check the NFRC label before you buy.

Why are ProVia doors more expensive than big-box doors?

You're paying for thicker fiberglass skins, better core insulation, better hardware, broader configuration options, and a manufacturer warranty that actually pays out. ProVia doors are typically 30-50% more than a comparable big-box product and last roughly twice as long in our climate. I cover the cost detail at ProVia Windows and Doors Cost.

Does Modex install doors as a standalone job?

Sometimes. We focus on door projects when we're already replacing windows on the same house — that's where our pricing is most competitive. If you have one or two doors and no other exterior work planned, I'll usually recommend a door specialist. If you're doing a window replacement and a door project together, we're the right call.

Ready for real pricing on your door project? Call Modern Exterior Systems at 952-206-6339 or request a free quote online. Free measurement, honest numbers, no high-pressure sales.

Modern Exterior Systems is a women-owned, family-operated exterior contractor based in Eden Prairie, MN, serving Minneapolis, St. Paul, and 90+ Twin Cities communities. Owner Joe Dvorak brings decades of hands-on construction experience, CertainTeed ShingleMaster and Malarkey Emerald certifications, and a Lifetime workmanship warranty to every residential project. BBB Accredited with an A+ rating.